Announcements • Re: 📣 WinBox 4 is here 📣
Winbox IPv6 connectivity, when?Its 2025, i shouldn't have to resort to IPv4 to manage an IPv6 forwarding device.this is already here for agesStatistics: Posted by spippan — Fri Apr 18, 2025 4:11 pm
View ArticleAnnouncements • Re: v7.19beta [testing] is released!
SUP-185949, reported CCR1072 v7.18.2 setup as PE with vpls and L3-VPN4 inside, having random rebooted by proper shutdown.if you find any miss configuration at least you can reply which configuration...
View ArticleGeneral • Re: WireGuard Traffic Issue
The config is far to complex for my level of understanding, however I will say that you give away addresses like candy to kids,and as far as I understand the single bridge should not have multiple IP...
View ArticleBeginner Basics • Re: Primary gateway with static ip address not activating
Post the output of:Code: /ip route printand of:Code: /ip address printYou seem to be using recursive for failover, and the behaviour has changed between 6.x and 7.x, you now need appropriate scope and...
View ArticleGeneral • Re: WireGuard connectivity issue assistance
Best to provide your config for review/export file=anynameyouwish (minus router serial number, any public WANIP information, keys),.\Steps1. Take the private key given to you and when you make an...
View ArticleBeginner Basics • Re: hEX refresh/ as Switch ->Pros & Cons?
Any hex device makes a great little managed switch that works great in a home setting or even an office setting.If one is in a corporate setting where, for example, the same vlan spans two or more...
View ArticleMikroTik hardware questions • Re: Chateau Pro ax - Wi-Fi radio stops...
Have the same issue on same device. It's because USB3 generates RF noise in Wifi 2.4GHz range.viewtopic.php?t=203470I've put usb cable and disk itself in aluminum foil to check if it's related to RF...
View ArticleMikroTik hardware questions • Re: RDS2216 Experience
Anyone had any luck with getting VMWare to successfully connect to an ISCSI partition on an RDS2216? - it seems as if the LUN being offered is not suitable to complete the connection and the ISX host...
View ArticleGeneral • Re: Dual WAN failover - check internet
Code: [xxxx@RB5009] > ping 8.8.8.8 interface=ether2 SEQ HOST SIZE TTL TIME STATUS 0 8.8.8.8 56 118 6ms676us 1 8.8.8.8 56 118 6ms529us 2 8.8.8.8 56 118 6ms519us sent=3 received=3 packet-loss=0%...
View ArticleGeneral • Re: Reliable addresses to ping on internet
Re: ... ping ... monitor an internet connection ...If I was going to try this , I think I would write up a Netwatch script.Have it ping multiple IPs out on the internet and then have the script detect...
View ArticleGeneral • Re: Respond for the internet connection through which they connect.
As you may have guessed the responders have some WHAT IFs, and other suggestions ( and also some errors).In other words, you should not be asking for a part solution if the requirements are not fully...
View ArticleWireless Networking • Re: hEX and CAP ac
I use my capacs with my hex without capsman its quick and easy to config. Your hair will not turn gray or fall out!!Statistics: Posted by anav — Fri Apr 25, 2025 7:06 pm
View ArticleBeginner Basics • Re: force subnet through specific gateway
draw a network diagram.Do you mean you have two WAN connections?Do you mean you have two Subnets?Etc..............Statistics: Posted by anav — Fri Apr 25, 2025 7:08 pm
View ArticleGeneral • Re: SXT LTE6 Kit lte problem
Some weird magic. I put SIM card of other mobile operator (Lifecell), i get normal IP address 10.160.107.49 but still no ping from SXT and from lan. When I uncheck Use network APN and set apn...
View ArticleGeneral • Re: VRRP Stuck in Master in both devices
Just for knowledge, I was stuck in the same issue, I tried to downgrade routeros firmware but I was stuck in the master/master issue.Finally I found the problem: I was using "Trunk channel" for the...
View ArticleGeneral • Can not access the CPU via incomming vlan !! :(
Hello,I am actually managing my CRS317 RouterOS 7.18.2 via the console. However I try to manage the switch via a VLAN arriving from my firewall. Since I did not manage that using the main bridge. I...
View ArticleBeginner Basics • Troubles to add new CAP to my network
Hi guys,after long time I decided to play a bit with my network by adding new device - cAP ax. My config is:CRS125-24G-1S-2HnD as CAPsMANGroove A52-HPn as CAPcAP lite AP as CAPAll running 7.18.2I've...
View ArticleGeneral • Re: Connectivity Issues after Upgrade 7.17.2 > 7.18 / 7.18.2
Hi,Versions v7.18.2 and 7.19betaXX are broken for IPSEC in hexS.Simple example:LAN site A (SIP videophone) <--> IPSEC <--> LAN site B (video intercom)- SIP calls --> OK- Video calls...
View ArticleBeginner Basics • Re: Troubles to add new CAP to my network
AX devices can't be controlled though "old"/wireless capsman.You need to run wifi capsman which is available in 7.XAs you have a crs125 as capsman and cap lite as caps you will need both wireless and...
View ArticleBeginner Basics • Re: ultra Slow Upload, Download fast
Hi,Yes definitely know the difference. sorry for confusing, but your comment is useless.My ISP grants me about 100 Mbps Upload, and I reach 5-10. I get full upload speed (70 to 95 Mbps) with the cheap...
View ArticleWireless Networking • Multi-passphrase VLAN issue
Device: hAP ax³RouterOS: 7.18.2I currently have three Wi-Fi interfaces, one of which is a guest network:Code: /interface wifiset [ find default-name=wifi1 ] configuration=5GHz disabled=no...
View ArticleWireless Networking • Re: Querying CCQ values via SNMP is not possible with...
On the Station device:Rx CCQ: 1.3.6.1.4.1.14988.1.1.1.1.1.10.(link_index)Tx CCQ: 1.3.6.1.4.1.14988.1.1.1.1.1.9.(link_index)I can't recall how to get the link index number though. Although I added the...
View ArticleAnnouncements • Re: v7.18.2 [stable] is released!
Recently, my routers have stopped performing DNS lookups when using DoH and verify-doh-cert turned on. I noticed that the valid dates for certificates are incorrect. Here is a fresh config using...
View ArticleWireless Networking • Re: Multi-passphrase VLAN issue
Just guessing ... I think that wifiX bridge ports should be set as tagged members of relevant VLANs ... all that are used in multi-passphrase configuration.Statistics: Posted by mkx — Fri Apr 25, 2025...
View ArticleGeneral • Re: RB5900: Sporadic SFP link failures
I experienced this issue after and update from 7.12.1 to 7.17 Reverted back to 7.12.1 and this issue occurs only 1-2 times/day instead of 5-6/hours on 7.17.Statistics: Posted by jhaxhiaj — Fri Apr 25,...
View ArticleBeginner Basics • Re: DNS Issue
Hi MTNick, this is working well but can you please explain the raw rules, are they built to drop any packet coming from non certified DNS servers ?Many thanks for your help, your proposed...
View ArticleGeneral • how to increase buffer size for a DNS container using doq
using a ctrld proxy container for DNS requests. when enabling doq , it complains about buffer size which seems to be derived from underlying OS(routerOS):2025/04/25 20:24:54 failed to sufficiently...
View ArticleForwarding Protocols • MikroTik BGP ECMP Behavior and Preferential Routing
I'm running a MikroTik router (CCR1009) on RouterOS 7.18.2 and I'm trying to achieve a clean and reliable dual-uplink BGP setup with two providers:ISP1 (Primary)ISP2 (Backup)I am receiving full...
View ArticleAnnouncements • Re: Newsletter #124
Any chance we'll see OFDMA on the 'ax products? I can't see any mention of this feature in change logs.Almost a year ago I posted (viewtopic.php?t=208144) and got zero responses.Statistics: Posted by...
View ArticleRouterOS beta • Re: FEATURE REQUEST: full cone NAT
I was able to achieve full cone NAT on RouterOS 7.13.5 using the following NAT rules:Code: add action=endpoint-independent-nat chain=srcnat out-interface-list=WAN protocol=udp randomise-ports=noadd...
View ArticleGeneral • Re: need 16121.1034.00.01.01.09 for hAP ax lite6
exactly I have seen too that the release 3 is working but other are not working.[...]The .9 is not working. I tried updating to the latest beta with no resolution of the issue.Do firmware upgrades of...
View ArticleGeneral • Re: Can not access the CPU via incomming vlan !! :(
Is this the same device that mkx was trying to help you with??Statistics: Posted by anav — Sat Apr 26, 2025 4:29 am
View ArticleGeneral • Netwatch UP threshold
What are the default thresholds for a netwatch script to mark a check as UP? I have found forum responses where it seems there used to be netwatch attributes such as success-count but these do not...
View ArticleAnnouncements • Re: New exciting features for storage
I just found out today that Unifi offers something called "unifi drive" which is some NAS solution since Q4/24 or something. So quite new as well. I did not look at its specs in detail nor did I...
View ArticleGeneral • Re: Netwatch UP threshold
The netwatch ICMP is (IMHO) complex and mis- or under- documented.However (from what I understand) the logic seems to be like a double negation, UP is "NOT down".But then I don't understand why you...
View ArticleContainers • Re: TeamSpeak 5 docker
hi! I also want to set up teamspeak3 on a Mikrotik 5009, but I absolutely don't understand where to dig.I tried to set up a container bartixxx32/teamspeak3:latest-aarch64 and mount the folder...
View ArticleGeneral • Dual WAN Failover script - feedback pls
After hours spent trying to get netwatch to work for me I ended up writing my own failover script. Would be happy to hear peoples suggestions on what I have come up...
View ArticleMikroTik hardware questions • Interesting Behaviour with BaseT (RJ45) SFP+...
I was recently testing using a 5G device (it does 5G, 2.5G and 1G only unlike the 6 speeds of Mikrotik's S+RJ10) When connected to a remote device at 5G and 2.5G it requires the backend to be running...
View ArticleGeneral • Device-mode not in backup
I would REALLY like to have any Device-mode/update changes I make stored in the backup please Statistics: Posted by Xymox — Sat Apr 26, 2025 1:49 pm
View Article